Trade Agreement: NAFTA/AIT/Canada-Peru FTA/Canada-Colombia FTA
Tendering Procedures: Generally only one firm has been invited
to bid
Attachment: None
Non-Competitive Procurement Strategy: Exclusive Rights
Comprehensive Land Claim Agreement: No
Vendor Name and Address:
Power Source Instruments Inc.
1111 Burns Street East, Unit 1
Whitby Ontario
Canada
L1N6A6
Nature of Requirements:
True Three Phase Field Testing Analyzer
U6322-120001/A
Martin, Lesley
Telephone No. - (905) 615-2076 ( )
Fax No. - (905) 615-2060
Industry Canada has a requirement for the supply and delivery of
three (3) 5-Series Powermaster (5300) on or before March 28,
2013.
Industry Canada's field test installations are designed to
acccept specific connection interfaces. A critical component to
IC's measurement is the input of correction factors for
increased accuracy.
The True Three Phase Field Testing Analyzer must meet the
following mandatory specifications:
General Specifications
Accuracy Class of +/- 0.05% or greater
Operating Temperature: -20 deg C to 50 deg C
Storage Temperature: -30 deg C to 60 deg C
Humidity: 0 to 90% or greater, non-condensing
Dimensions: 540 mm x 440 mm x 220 mm or less
Weight: 30 lbs or less
Display / Software Specifications
8.0 inch display or greater
Full colour, transflective display
Resolution of 0.001% of display value
Windows based operating system
Display complete vector diagrams (Colour Plot)
Display % registration of customer load meter test results per
measurement function
Display individual waveforms, for voltage, current, power (Plot)
Display complete CT Burden Results in form of Accuracy
Parallelograms per pahse, including ratio and phase error's
Display complete Harmonic Analysis Results (Plot)
Display demand test data results
Simultaneously display complete site analysis summary including
vector diagram (plot), waveforms (plot), harmonic analysis
(plot) and customer load test date
Programmed with all Canadian (MC Standard) Meter Drawings
Technical Specifications
Voltage Inputs
4 inputs/ channels
Measures 10 volts to 600 volts (rms) with a resolution of 1
micro volt
Auto-ranging with an accuracy of 0.08% of reading or better
All four voltage leads must be fused with a CAT III (1000 V)
rating and connect via a multi pin connector
Current Inputs
3 direct inputs / channels
Measure from 0.1 to 20 amps with a resolution of 1 micro amp and
an accuracy of 0.08% of reading or better
6 probe set inputs / channels to accept clamp on probes, flex
probes and amp lite wire probs.
Connection via multi pin connectors
Frequency
Must maintain specified accurazy when measuring a system
frequency between 45 and 65 Hz
Energy Measurements
Provide measurements of watt hours (wh's), volt amp hours
(vah's) and Volt amp reactance hours (varh's)
Measurements must be user selectable
Power Measurements
Provide measurements of watts (w), volt amps (va), and volt amp
reactance (var)
Measurements must be user selectable
Burden Testing
Apply and measure the effects on the CT's secondary output
accuracy, when additional burdens (resistances) are applied to
the CT
Required burdens to be applied are 0.1 ohms, 0.3 ohms, 0.5 ohm,
1.0 ohms, 2.0 ohms, and 4.0 ohms
Ratio Testing
Conduct ratio and phase angle tests between actual primary and
secondary currents to an accuracy of 0.2% or greater
Phase Angle
Measures a phase angle of 0 to 360 degrees with a resolution of
0.2 degrees or better
Power Factor
Measures power factor from -1.00 to +1.00
Harmonic Analysis
Measures the 50th Harmonic or greater
Must measure THD, Total Harmonic Distortion
Memory
Store a minimum of 150 individual sites in non-volatile memory
Auxiliary Power
Minimum range of 120 volts to 530 volts or greater
Must have a built in charging unit
The only known supplier of a system meeting the technical
specifications required is Power Source Instruments Inc.. For
this reason it is proposed to negotiate directly with them for
this requirement.
Single sourcing applies under the following:
-GCR. Section 6d) : Only one person is capable of performing the
contract.
-AIT, Article 506.12 a) : to ensure compatibility with existing
products, to recognize exclusive rights, such as exclusive
licences, copyright and patent rights, or to maintain
specialized products that must be maintained by the manufacturer
or its representative.
NAFTA, Article 1016.2 b): Where, for works of art, or for
reasons connected with the protection of patents, copyrights or
other exclusive rights, or proprietary information or where
there is an absence of competition for technical reasons, the
goods or services can be supplied only by a particular supplier
and no reasonable alternative or substitute exists.
Delivery Date: Above-mentioned
You are hereby notified that the government intends to negotiate
with one firm only as identified above. Should you have any
questions concerning this requirement, contact the contracting
officer identified above.
An Advance Contract Award Notice (ACAN) allows departments and
agencies to post a notice, for no less than fifteen (15)
calendar days, indicating to the supplier community that it
intends to award a good, service or construction contract to a
pre-identified contractor. If no other supplier submits, on or
before the closing date, a Statement of Capabilities that meets
the requirements set out in the ACAN, the contracting authority
may then proceed with the award. However, should a Statement of
Capabilities be found to meet the requirements set out in the
ACAN, then the contracting authority will proceed to a full
tendering process.
Suppliers who consider themselves fully qualified and available
to provide the services/goods described herein, may submit a
statement of capabilities in writing to the contact person
identified in this Notice on or before the closing date of this
Notice. The statement of capabilities must clearly demonstrate
how the supplier meets the advertised requirements.
The PWGSC file number, the contracting officer's name and the
closing date of the ACAN must appear on the outside of the
envelope in block letters or, in the case of a facsimile
transmission, on the covering page.
The Crown retains the right to negotiate with suppliers on any
procurement.
Documents may be submitted in either official language of Canada.
